2012 SSO ACU black tactical uniform used by CSN of FSB

Price $280 (item number: #929)

Price do not include shipping, shipping costs are calculated separately after placing an order, depending on the location and weight of the items.

SSO (SPOSN) ACU uniform black tactical suit.
Made from rip-stop fabric. Wind moisture protected.
Made in ~2012-2014. You can see this suits on FSB TsSN unit members during special operations (Dagestan, North-Caucasus area) and trainings.

Size at photo: 54-56/180-185 (labels removed by servicemen)
Have another size, please send message with size you want.

Was used by FSB russian spetsnaz Alfa / Vympel and regional FSB teams.

The suit consists of a jacket and trousers.

The jacket is not too long; in the buttoned position, its lower cut is slightly lower than the lower back. The stand-up collar fastens with a Velcro closure. One of the edges of the collar can be folded down and fixed, for its part, with additional Velcro, leaving the collar itself open. The jacket fastens at the front, from the lower cut to the collar, with a durable YKK polyamide zipper. The zipper is covered with a strap fixed by three velcro locks: from above, in the middle and from below. On the front, in the chest of the jacket, on the right and on the left, there is a small (160x130 mm) flat patch pocket. The vertical entrances to these pockets, slightly slanted vertically (for easy access), are located on the side of the central zipper, and are securely closed by small valves on Velcro closures, across the entire width of the entrance. Slightly higher than each of the breast pockets, one sewn-in strap with Velcro mate is horizontally located for attaching identification chevrons and signs. Another small similar platform for attaching chevrons is located in the central chest of the jacket on the outside of the strap covering the zipper. On the sleeves of the jacket, in their upper part, there is a patch pocket (160x120 mm) with one side cut-in wedge, for a small increase in volume. These pockets are very convenient in cases where access to the breastplates is difficult when additional equipment is worn on top. Sleeve pockets are closed by valves with double Velcro closures. For greater convenience, these valves have an additional strap that can be grabbed by a gloved hand, or if the hand is frozen or injured. If they are not necessary, the straps can be removed under the valves, fastening them to the inner Velcro. The entire outer area of the sleeve pockets, including the surface of their flaps, is sheathed in velcro mate, forming convenient platforms for attaching stripes, chevrons and decals. In the upper dorsal part, from its right and left edges, the jacket has two hidden vertical mortise wedges. These wedges give the user greater convenience in complex and sharp movements, without restricting or pulling the fabric, and also contribute to better ventilation of the back in hot weather. The sleeves of the jacket, in the region of the elbow joints, have a flat pocket-patch made of an additional layer of fabric, closed with a Velcro closure. If necessary, a piece of “foam” can be inserted into this pocket, forming an internal soft elbow piece. Cuffs of sleeves are reinforced with a double layer of fabric, are adjustable and fastened with Velcro closures.

The pants of the ACU suit have a loose cut. The waist part of the trousers is reinforced with a double layer of fabric, has an internal adjustable tightening with a built-in cord. Outside the waist part there are seven belt slats with a dial arrangement for 1, 3, 5, 6, 7, 9 and 11 hours. The size of the swivels allows the use of trouser belts up to 50 mm wide. The wide section of the trousers and its four plastic buttons are covered with a double layer fabric flap. In front of the trousers, immediately below the belt, deep classic mortise pockets are located on both sides. Below, on both sides, there are large (240x200 mm) patch lateral hip pockets, closed by slightly sloping (down and forward from the horizontal) flaps on two Velcro closures. These pockets have three vertical mortise wedges, if necessary, slightly increasing their volume. In addition, the hip pockets, in their upper cut, can be pulled in by an integrated rubberized cord with a plastic clip. There is also a small patch pocket (170x100 mm) on the outer sides of both legs. Pockets are closed with small flaps on a double velcro closure. Two flush pockets (140x170 mm), closed by valves on two buttons, are located in the buttock of the trousers. The sciatic part is reinforced with a double layer of tissue. The lower sections of the trousers are also reinforced with a double layer of fabric and pulled by ribbons. In the area of the knee joint location, both trousers have a velcro-fastened, flat pocket with an additional layer of fabric. If necessary, a “foam” is inserted into these pockets to create an internal soft knee pad. All straight seams of the product are made according to the technology of a seam with double hem. The patch pockets and pocket valves are sewn in the same seam. All corners of the joints are reinforced with zigzag tack.

Was manufactured under government contract special and on terms of reference of FSB.

This type was not offered in civil stores.

Now you have chance to buy it and be sure that this item was 100% originally used by this team.